New Portable VNA SWR Vector Network Analyzer Reflectometer Arinst 23-6200 MHz

Description

NEW Informations: This device is sold without a battery inside, due to problems with air transportation by mail.
You will need to separately purchase such a battery and independently install it inside, simply glue it on a bilateral tape.
This is easy, there is a connector.
Sale
only without a battery
! ! !
Reason: Return from the airport due to the presence of a lithium battery inside.
Required battery: Lithium no.
505080. 3000 mAh, 3.7V  with connector 2.54mm.
Dimensioms: 80x48x5 mm
----------------------------------------
Portable vector network analyzer VNA (reflectometer) ARINST VR 23-6200 MHz
is designed to measure the matching characteristics of passive and active radio devices (antennas, cables, filters, attenuators, amplifiers, etc.).
The device allows you to measure the parameters of the complex reflection coefficient, standing wave ratio (VSWR), impedance, admittance, magnitude, phase, loss and distance to fault in the cable.
Manual:
arinst.net/files/Manual_Vector_reflectometer_Arinst_VR_23-6200_ENG.pdf
For whom?
VNA ARINST VR 23-6200
is made in a durable aluminum casing in the form of mobile autonomous instrument and is primarily intended to work directly on the object, as with low weight and compact dimensions has a low energy consumption. The analyzer will be especially useful to companies working in the field of telecommunications, engaged in the installation and maintenance of antennas, in the amplification of cellular communication, etc. With it, service centers and repair crews can carry out RF analysis cable and antenna when carrying out commissioning or repair work. In addition, the device is ideal for workshops, radio amateurs, educational institutions and laboratories.
The device has a 3.2" color resistive screen to display the measurement results and control the device.
For example, you can use the instrument to do the following:
To perform impedance matching using the Smith chart
To measure the standing wave ratio
To measure the attenuation in the cable
To measure the distance to fault or irregularity in the cable
External USB control from PC is provided.
Advantages of vector network analyzer ARINST VR 23-6200 MHz
:
color touch screen with a diagonal of 3.2 inches allows for quick configuration of the scan parameters and display of measurement results
wide operating frequency range: 23 MHz to 6200 MHz
high scan rate of 1000 points/s
high precision of measurement: 0.25 dB and 1.5° over the entire frequency range
the ability to display up to four independent markers on all charts, allowing an accurate assessment of the measured parameter
display almost all possible interpretations of the reflection coefficient
the ability to measure the distance to fault and loss in the cable
small weight and dimensions: 400 grams with "pocket" dimensions 155×81×27 mm
built-in battery provides up to 2 hours of battery life
ability to power the device from a tablet or smartphone via USB OTG cable: not in time discharged battery will not stop the workflow
SPECIFICATIONS ARINST VR 23-6200 MHz:
Operating frequency range
23-6200 MHz
The frequency resolution
10 kHz
Maximum number of scan points
1000
Scanning rate
1000 points/s
The direction of the bridge, uncorrected throughout the range
>12 dB
Directivity effective (after full single-port calibration)1
>50 dB
The standing wave ratio at the input
<2
Phase measurement precision1
>1.50
Magnitude measurement precision1
>0.25 dB
Resolution determining the distance to fault2
(C x VF)/2S m
The maximum length of the measured cable3, with VF =1
3000 m
Maximum DC input voltage
25 V
Displayed graphs
the Smith chart; polar chart; the phase of the reflection coefficient; magnitude; logarithmic magnitude; VSWR, distance-to-fault; cable loss
Operating temperature range
0...+40
°
С
Screen diagonal
3,2"
Screen type
touch
resistive
Screen resolution
320х240
Battery capacity
2500 mAh
Continuous battery life4
~2 h
Battery charge time
~6 h
Overall dimensions (L×W×h)
155×81×27
Mass
0.4 kg
1 The measurement is performed after warming up the device for at least five minutes with a full (short, open, load) single-port calibration. The change in ambient temperature from the time of calibration to the time of measurement shall not exceed ±3 °C.
2 Where C is the speed of light m/s; VF is the speed factor (the ratio of the speed of propagation of the electromagnetic wave in the cable to the speed of propagation of the electromagnetic wave in vacuum), takes a value depending on the cable from 0.1 to 1; S is the scanning frequency range in the frequency task (Hz).
3 Depends on the amount of attenuation in the cable and is the limit of the display.
4 At ambient temperature plus 20±5°C after full charge.
The device has a factory calibration, the device connector is taken as the reference plane. If you plan to carry out measurements using cable assemblies, adapters, etc., then you will need to recalibrate. To do this, use the 50 Ohm calibration kit SOL (S- Short Standart - O -Open Standart  L - Matched Load). SOL calibration kits are most often found in the
N-type
and
SMA-type
form factors. Choose the form factor corresponding to the type of connector, on the reference plane of which calibration is planned.
Equipment:
ARINST Vector Reflectometer 23-6200 MHz
USB connection cable
Packaging
Overview of the device
Video "Vector Reflectometer ARINST VR 23-6200 VS Agilent E8358A"   youtube.com/watch?v=Iw94cG4UcM
Additional Information
The device has a manufacturer's warranty for 1 year from the date of purchase
NEW Informations: This device is sold without a battery inside, due to problems with air transportation by mail.
You will need to separately purchase such a battery and independently install it inside, simply glue it on a bilateral tape.
This is easy, there is a connector.
Sale
only without a battery
! ! !
Reason: Return from the airport due to the presence of a lithium battery inside.
Required battery: Lithium no.
505080. 3000 mAh, 3.7V  with connector 2.54mm.
Dimensioms: 80x48x5 mm